![]() You may have to go ahead and glass bed the rifle after the fix or even use full barrel channel bedding. If your barrel is freefloated, the fix may not affect your POI and accuracy or it may depending on workmanship, receiver bedding,etc. Clear epoxies rather than gray JB weld are easier to hide. You can also use epoxy alone available at any hardware store-use the type specified for wood-make sure crack is clean, apply, clamp, etc. Acraglas has a brownish tint so it does blend into dark wood, resembling wood grain, you can add a black colorant to it. You can use acraglas which is a two part resin based adhesive-spread the crack, apply, clamp, and make sure to cover areas on the stock's surface with paste wax, or some other epoxy. It will be seen, but may add "character" to the rifle. after the glue sets, cut the rod on both sides, use a file to file it down to the level of the wood, refinish the wood in those two areas. to the threaded rod and inside the hole across the stock, screw the rod through the hole, clamp, etc. The old time version of this is to use brass threaded rod, drill a hole through the crack, apply glue/epoxy/etc. Cut a wood slot in the barrel channel (dremel, hobby knife, oscillating saw, whatever), lay the cleaned (acetone, etc.) threaded rod in the slot across the crack, use clear epoxy to cover the threaded rod (even a small bolt with a nut works). A way to strengthen that repair is to use some sort of threaded rod-preferably one that does not rust, you will have to work within the barrel channel if you do not want the repair seen so the stock is going to have to be dismounted from the action. The thick glue resists wicking into the crack so it may have to be manually applied. You will need to actually wedge the crack a bit to open it to the wood glue-thinner glue generally wicks better but is weaker. The weakest fix is simply using a very good wood glue (in heavens name no foaming resin type glue like Gorilla Glue) and clamping it. Others will probably also post but 1) it is fixable, 2) it may not be as accurate post fix without some additional work, and 3) are replacement stocks available if you mess up. )? I am guessing from the wood that it is a stained beech stock which means depending on the repair needed, you may have to refinish around the repair. Is the barrel free floated and do you have any kind of indication about how accurate it was pre repair (groups etc. Since this is a satin finished stock you may have to experiment with the grits to blend in the repair in the most unobtrusive way. And last, but of much importance - always use water while sanding polymer finishes (varnish). ![]() If you put too much glue, first level it with coarser grits - like 1000 grit sandpaper backed by a piece of thick leather, or the coarser side of a nail polishing file (block). Use it sparingly! For blending in the repair you can polish it with a fine nail polishing file. On the outside use the same CA glue to fill the scratches - you can use a needle for applicator. If you don't feel confident with that just put the glue on the crack - it will work it's way in. Fill the gap from the inside, while trying to expand it (gently!) with a thin knife blade, or something similar. Since this is a non load bearing part of the stock, a thin, low viscosity CA glue (like Loctite 401) will do the work. 311 bullets, some American brass ammo may not perform as well as the imported steel-cased variety because of SAAMI brass dimensions and varying bullet diameters.There is nothing to worry about, this is a minor damage and it's easily repairable. Both chamberings offered in the Carbine are economical to shoot given their service rifle heritage and the availability of surplus ammunition.īuilt to CIP specifications, CZ’s 7.62×39 chambers are ideal for shooting steel-cased surplus ammo. For a long time this was CZ’s only model chambered in 7.62×39 (now joined by the 527 Youth Carbine), it combines low recoil with effectiveness on medium-sized game such as deer and wild boar, making it ideal for younger shooters. The Carbine is an intermediate range ‘brush gun.’ Weighing in at less than 6 lbs, this handy rifle has a straight comb walnut stock and open sights. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |